Details Of The 2 X 24 Flat Turret Lathe With Chucking Inches Diameter

The Machine One 2 x 24 by 12-inch swing Flat ------ Turret Lathe, Cross-feed Head,

Single Drive, six Tool Blocks, four Tool Holders, Oil Pump and Piping, Friction Countershaft, Cast-iron Table for holding tools, etc., and suitable Wrenches.

Chucking Tools One 12-inch Face Plate.

=============== One 12-inch three-jawed Scroll

Chuck with reversible, three-step Jaws.

One extra set of Long-necked Jaws for inside gripping.

One extra set of Soft Blank Jaws that may be turned to fit any special form.

One dozen Outside Turning Cutters (one each 03, 06, 09; two each 04, 05, 07, and three 08).

Eight Inside Turning and Boring Cutters (one each 018, 019, 027, 028, and two each 016 and 017).

One 1 1/2 -inch Round Boring Bar, with two cutters.

One 2 1/2-inch Square Extension Turning Bar, with two clamps.

All may be briefly described as 2 x 24 Flat Turret Lathe, with Chucking Outfit (Outfit C).

Double Outfit For Bar And Chuck Work For Bar Work Up To 2 1/4 Inches In Diameter And 24 Inches In Length And Chuck Work Up To The 12-Inch Swing Capacity

The Machine One 2 x 24 Flat Turret Lathe,

========== Cross-feed Head, Single Drive, four Tool Holders, three Stock Supports, Oil Pump and Piping, Friction Countershaft, Cast-iron Table for holding tools, etc., and suitable Wrenches.

Parts for handling the bar of stock Automatic

======================== Chuck and

Roller Feed. Fifteen sets of Jaws for chuck, holding all sizes from 1/2 inch to 2 1/4 inches in diameter, inclusive.

Turning Tools Four Quick-opening Turners, ad-

========== justable to all sizes from 2 1/4 inches down.

One Cross Slide for holding cutting-off and forming tools.

One Pointing Tool.

Screw Thread Cutting One 1 1/4-inch Automatic ==================- (opening) Die, with fifteen sets of chasers for cutting all U. S. S. threads 3/8 of an inch to 1 1/4 inches in diameter, inclusive, by sixteenths.

Chucking Six Tool Blocks.

One 12-inch Face Plate.

One 12-inch three-jawed Scroll Chuck with reversible, three-step Jaws.

One extra set of Long-necked Jaws for inside gripping.

One extra set of Soft Blank Jaws that may be turned to fit any special form.

One dozen Outside Turning Cutters (one each 03, 06, 09; two each 04, 05, 07, and three 08).

Eight Inside Turning and Boring Cutters (one each 018, 019, 027, 028, and two each 016 and

017).

One 1 1/2 -inch Round Boring Bar, with two cutters.

One 2 1/2 inch Square Extension Turning Bar, with two clamps.

All the above may be briefly described as 2 x 24 Flat Turret Lathe, with Automatic Die and Chucking Outfits (Outfits D and C).

Details Of Outfit Of Tools For Bar Work Handling Full-Length Bars Up To 3 Inches Diameter Turning All Diameters Up To 3 Inches And Threading Up To 2 Inches Diameter

The Machine One 3 x 36 Flat Turret Lathe, =========== Cross-feed Head, Single Drive, four Tool Holders, three Stock Supports, Oil Pump and Piping, Friction Countershaft, Cast-iron Table for holding tools, etc., and suitable Wrenches.

Parts for handling the bar of stock Automatic

=========================== Chuck and Roller Feed. Seventeen sets of Jaws for chuck, holding all sizes from 1 inch to 3 inches in diameter, inclusive.

Turning Tools Four Quick - opening Turners,

============ adjustable to all sizes from 3 inches down.

One Cross Slide for holding cutting-off and forming tools. One Pointing Tool.

Screw Thread Cutting One 2 - inch Automatic =================== (opening) Die, with nine sets of chasers for cutting all U. S. S. threads 1 inch to 2 inches in diameter, inclusive, by eighths.

All the above may be briefly described as 3 x 36 Flat Turret Lathe, with the Automatic Die Outfit (Outfit D).