This first movement of passengers by steam in the State of New Jersey was regarded as a success from every point of view, and in commemoration of the important events here enacted the boundaries of this first piece of railway laid between New York and Philadelphia, which were identified and staked out by Isaac Dripps a half century afterward, have been definitely marked for all time by the Pennsylvania Railroad Company, who have erected these handsome stones.

Early Difficulties

Among the earliest troubles of the young engineer and his employer, Robert L. Stevens, was the fact that as there were only four wheels under the engines, they were derailed frequently in going around curves; so it was necessary to provide an appliance to prevent this.

The First Pilot

The first pilot was planned, 1832, by Robert L. Stevens. A frame made of oak, eight by four feet, pinned together at the corners, was made. Under one end of it a pair of wheels twenty-six inches in diameter were placed in boxes, and the other end was fastened to an extension of the axle outside of the forward driving wheels, it having been found by experience that a play of about one inch on each side on the pedestals of the front wheels of the pilot or engine was necessary in order to get around the curves then in the tracks. For years afterward there was very little change in constructing the pilots from that originally applied to the "John Bull."

The spiral spring, which held the front wheels of the pilot in place, acted substantially as the center pin of a truck. The turntables in use on the road were so short that it was necessary to unconnect and take off these pilots before turning the engine. After the pilot was adopted the forward large wheel on right of the engine was made loose on the shaft in order to afford additional play in going around curves. Other6 changes and additions were also made in the locomotive.

Improvements In Locomotive Building

During 1831-35 the company's shops were located at Hoboken, N.J., and during the winter of 1832-33, three locomotives were commenced at these shops (two completed before March, 1833, the other in April), the valves, cylinders, pistons, etc., coming from England, the boilers being made under the direction of Robert L. Stevens. It was his opinion that the "John Bull" was too heavy, and the new boilers were built smaller and lighter, so that the engines, when completed, weighed eight instead of ten tons. With these three engines, which were delivered to the railroad company at South Amboy, the stone blocks and other material for the permanent track was delivered along the line of the road.

Baldwin's First Locomotives

The importation of the locomotive "John Bull" was destined to have a far-reaching influence in moulding the types of early American locomotives.

After the demonstration of November 12, 1831, the engine was taken from the track and stored in a shed constructed to protect it until such time as the track should be completed.

It was about this time that the proprietor of Peale's Museum, in Philadelphia, applied to Matthias Baldwin, an ingenious mathematical instrument maker, for a small locomotive to run upon a circular track on the floor of the museum. Mr. Baldwin had heard of this locomotive. He came to Bordentown and applied to Isaac Dripps for permission to inspect it. Mr. Dripps tells me he remembers very well the day that he explained to Mr. Baldwin the construction of the various working parts.

Mr. Baldwin built a toy engine for Mr. Peale, which was so successful, that in 1832 he was called upon by the Philadelphia and Germantown Railroad Company to construct the old "Ironsides,"7 which was similar in many ways to the "John Bull," as an examination of the model preserved in the National Museum will show. The success of this engine laid the foundation for the great Baldwin Locomotive Works, which is in existence to-day, sending locomotives to every part of the globe.

The Line From Bordentown To South Amboy

The Camden and Amboy Company having obtained control of the steamboat routes between Philadelphia and Bordentown, and between South Amboy and New York, directed their energies to completing the railway across the State.

Although the grading of the road from Bordentown to Camden had been commenced in the summer of 1831, work on that end of the line was abandoned for about two years, the entire construction force being put on the work between Bordentown and South Amboy.

The road from Bordentown to Hightstown was completed by the middle of September, 1832, and from Hightstown to South Amboy in the December following. The "deep cut" at South Amboy, and the curves of the track there, gave the civil engineers great trouble.

The First American Standard Track

The laying of the track through the "deep cut" led to an event of great importance to future railway construction. The authorities at Sing Sing having failed to deliver the stone blocks rapidly enough, Mr. Stevens ordered hewn wooden cross ties to be laid temporarily, and the rail to be directly spiked thereto. A number of these ties were laid on the sharpest curves in the cut. They showed such satisfactory properties when the road began to be operated that they were permitted to remain, and the stone blocks already in the track were replaced by wooden ties as rapidly as practicable. Without doubt the piece of track in "deep cut" was the first in the world to be laid according to the present American practice of spiking the rail directly to the cross tie.

The Line Opened Between Bordentown And South Amboy

Among the memoranda compiled by Benjamin Fish, published in his memoir, I find the following:

"First cars were put on the Camden and Amboy Railroad September 19, 1832. They were drawn by two horses. They took the directors and a few friends from Bordentown to Hightstown and back.