This section is from the book "Amateur Work Magazine Vol3". Also available from Amazon: Amateur Work.
Robert Gibson Griswold.
The following described set of weights is intended to go with, or be used with, the balance described in the last issue of Amateur Work. The balance cannot be of much use without a set of good, accurate weights, and while the set if purchased from the maker's would be very accurate, they would cost about $10. Since every weight must be made by hand, however expensive it may be, the amateur can make them as well as the manufacturer.
In the first place, a set of weights need not be exactly a counterpart of the international standard, which the manufacturers always make them. The value of any set of weights lie in their being exact multiples or sub-multiples of each other, as every weight is simply relative and nothing absolute can be made. The system of weights generally used in all technical work, especially chemistry, physics and photography, is the international gram, the equivalent of which is a cubic centimeter of distilled water at its maximum density.
Now when a formula requires that the weight of a certain substance shall be say 9.647 grams, and that another ingredient shall weigh 7.523 grams, it makes no difference whether the weights with which the above ingredients are weighed out are exactly duplicates of the international standard or not, so long as the system to which the respective weights belong exactly agrees with its several units. To make this still plainer, the weights merely express the number of parts to be taken, so that if the unit to which the part is referred is the same in each case, the ratio between the ingredients will be correct.
Now in order that a starting place may be had from which to work, it will be necessary to borrow from some druggist or chemist a few weights for comparison. We will consider the making of the set of metric weights specified in the accompanying table denominations.
The above set will permit accurate weighings to be made from 200 grams down to 1 milligram, a range that is generally sufficient for all purposes. The combination given will permit any weight being readily ascertained with the greatest ease, giving the least number of trials. The writer prefers, in the case of the small weights, to make them of aluminum wire, as the pieces are larger and more readily handled than those made of foil. For the milligram weights use No. 34 B. & S. guage; for the tens of milligrams, use No. 28 or 30, and for the hundreds use No. 20 or 22. The larger weights are turned out of brass rods to the dimensions given below.
100 grams. | .5 grams | = 500 milligrams |
50 " | .2 " | 200 " (2) |
20 " | .1 " | 100 " |
10 " (2) | .05 " | 50 " |
5 " | .02 " | 20 " |
2 " (2) | .01 " | 10 " (2) |
1 " | .005 " | 5 " |
.002 " | 2 " (2) | |
.001 " | 1 " |
We will start with the milligram weight first. Adjust the balance accurately so that the needle swings to zero and stops there. Now place one of the borrowed milligram weights thereon and place on the other pan a short piece of the No. 34 wire and keep repeatedly trimming off the end with a sharp pair of scissors, or better yet, a sharp penknife, cutting down on to a piece of sheet zinc until it almost balances. Now remove the milligram weight and place on the pan holding the wire, which has been removed, and exactly .balance it with small grains of sand. This balance must be absolutely exact or else the following process will be of little value.
When a balance has been affected, remove the milligram weight and replace it by the piece of wire just cut. Now with a very smooth cut file, that has been boiled in soda to remove the film of grease always present on new files, and thoroughly dried, carefully file off the end of the wire and try its weight until it exactly balances the sand on the opposite pan and the needle stops at zero when through swinging. This is known as the method of substitution, and is the most accurate method of weighing in the ordinary balance that is yet known. It insures that the compared pieces shall be of exactly the same weight, regardless of the difference in the length of the two beam arms, however small this difference may be. This finishes the milligram weight. It should be particularly impressed that no weight should ever be touched by the fingers; always pick them up with a small pair of tweezers and if it is necessary to hold them in the fingers, do so with a piece of linen or silk between them and the skin. The skin is continually exuding moisture which will tarnish them.
Now place the two milligram weights on the pan together, and add more sand to the opposite pan until a balance is again secured. Cut off a piece of the wire slightly more than twice the length of the first piece and carefully adjust this by the method just given until it weighs exactly two milligrams. Then make another exactly like it. In the table given above those weights followed by the figure (2) are to be made in duplicate. We now have two two-milligram weights and a one milligram weight, the sum of which is five. Place the three on the pan together and balance with sand as before. Then cut another piece of wire as long as the three and adjust in a similar manner. If the work has been carefully performed the weights will be exact multiples of the milligram weight and the sum will be ten milligrams.
Now balance the ten milligrams against the ten milligram weight of the borrowed set and see that they balance perfectly. If they do not, go over the work carefully and see where the error lies. The ten milligram weight must balance these four weights just made, and the two 20's and 50 are made in exactly the same manner. All these wires should be bent into distinct shapes, the two's and 20 being bent into a V shape, the two arms indicating the denomination, and the five and 50 being bent into a pentagon or five sided figure.
The hundred milligram weights are made in a like manner, great care being taken to see that a strict multiple ratio is obtained in each. These fractional weights are the hardest to make and require considerable patience, but if well made are more than worth the time and trouble; and, furthermore, one has the knowledge that they are strictly accurate with each other, which is far more important than the material of which they are made or their respective shapes.
The larger weights are all made of brass and lacquered, the lacquer being put on and baked before they are adjusted. It is common to make the little handles loose and screw them into the weights, which permits of the adjustment being made on them by filing and then, when they are screwed into place, no bare metal is exposed to the action of dampness or fumes. Below is given a table of sizes to which a set may be turned up and afterwards adjusted. Of course it will be impossible to give a size that will be exact in every case, since the density of the metal will vary greatly in different compositions. But the figures will be a guide, and if the knobs are made loose and screwed into the weight, very little adjusting will be necessary and that only on the in side. If the weights are light, small pieces of tin-foil can be put in the hole before the knob is screwed in. This loose knob is provided merely to allow the entire outer surface to be lacquered, which it could not be if the adjustment had to be made by filing metal from the outside.
If the above set is carefully and properly made it will be well worth the time and trouble and with care in handling will last a lifetime. Weights should never be handled with anything but a pair of tweezers and they had best be ivory tipped. Make a neat wooden block and drill holes in it that will just fit the weights and always keep them in their respective places. The value of the weight may be stamped on its knob and also beside the respective holes in the block. Only slight depressions need be made for the fractional weights and they should be kept covered with a strip of glass. A cover should be provided for the block to exclude dust.

Value | A | B | c | D | E | F | G |
1 | 13-64 | 9-64 | 17-64 | 5-32 | 3-64 | 1-64 | 3-64 |
2 | 15-64 | 5-16 | 15-64 | 11-64 | 3-64 | 1-64 | 3-64 |
5 | 33-64 | 3-8 | 1-4 | 3-16 | 3-64 | 1-64 | 1-16 |
10 | 7-16 | 33-64 | 17-64 | 7-32 | 1-16 | 1-32 | 1-16 |
20 | 9-16 | 19-32 | 1-4 | 1-4 | 1-16 | 1-32 | 1-16 |
50 | 25-32 | 25-32 | 1-4 | 1-4 | 1-16 | 1-32 | 1-16 |
100 | 11-16 | 55-64 | 1-4 | 5-16 | 1-16 | 1-32 | 1.16 |
 
Continue to: