This section is from the book "Amateur Work Magazine Vol3". Also available from Amazon: Amateur Work.
W. M'ARTHUR
The developer may well be made up in bulk, as it keeps well. A special developer known as D salts is sold by the Platinotype Company, and gives admirable results, but neutral potassium oxalate works equally well, giving a good rich black which is preferred by many workers to the bluish black given by the D salts. As full particulars for use are issued with each packet of the D salts, it is unnecessary to detail them here.
In making up the potassium oxalate developer four ounces of the crystals are dissolved in forty ounces of water. A convenient way of making the solution is to tie the crystals in a piece of muslin and to suspend the bag so formed just be-low the surface of the water in a jug. Solution then takes place quickly, as the heavy liquid sinks to the bottom. If tap water is used the lime salts present in it will react with the oxalate and cause the solution to be opalescent. Except that it is more convenient to work with a clear solution this milkiness does no harm, but by allowing the solution to stand for a few hours the precipitate will settle and the clear liquid may be decanted into a suitable bottle or jar. From this stock solution sufficient for use may be taken and kept in a smaller bottle and used until it becomes loaded with iron salts from the paper, when it should be discarded. This is a better plan than to return the used solution to the stock bottle. If the potassium oxalate is bought from a reputable dealer it will be in a suitable condition for use, but if strongly alkaline it must be neutralized by the addition of a little of a saturated solution of oxalic acid. Slight acidity in the bath does not impair its action but tends to give cold black. Very slight alkalinity, which may be secured if wanted by the addition of potassium carbonate, gives brownish blacks. The developer is best used at a temperature of from 60 to 65 deg. Fahr. The clearing bath is made by adding one part of good hydrochloric acid to sixty parts of water. The very common variety known as spirits of salts should not be employed. If many prints are to be developed a large jugful of the clearing bath should be made up, as it must not be used sparingly or the iron will be left in the paper and become yellow in time.
A dish a size or two larger than the prints to be developed should have the developer poured into it to the depth of half an inch or more, and the same with the clearing bath.
The usual instructions are to float the paper face downwards on the developer, but in unaccustomed hands there is a tendency for air bells to form in this method of working. A simpler plan, and one to which there is no objection, is to hold the paper by one end face upwards and to slide it under the solution. If air bells form they are at once seen, and may be broken by shaking the dish. The moment the developer touches the paper development begins and is concluded in a very few minutes. It is desirable to expose the paper so that it may be left in the developer till the action is complete, though slightly over-exposed prints may be saved by removing them from the developer at an early stage.
After the print has been some thirty seconds in the developer, it will be seen that no further action takes place. It should then be removed to the clearing bath in which the yellow coloration is removed. At least three such baths should be used, and the prints should remain in each for five minutes, care being taken to prevent them from sticking together. If any trace of yellow color is seen in the last clearing bath, as may be the case if a number of prints are manipulated at one time, a fourth and even a fifth bath must be given. After clearing, the prints must be transferred to cold water and washed for twenty minutes, when they may be dried by laying them face downward on blotting paper or a clean towel.
To return to the trial strip, if the image has been printed to the correct depth, the remaining strips may be printed upon by way of practice, either from the same or other negatives, using the undeveloped piece that was cut off as a guide. It is, however, hardly likely that the first trial will be exactly right, or, if it is, that the success can be repeated with certainty until a little experience has been gained. It is well to select some point of detail in the lighter half-tone and to watch for the appearance of it when printing. The eye will soon become accustomed to the appearance of correctly exposed prints, and when that point is reached there is absolutely nothing more to learn.
I have said that prints that have been slightly over-exposed may be saved by removing them from the developer before the action is quite complete, when they should at once be placed in the clearing bath. I mention this, not to encourage carelessness in exposing, but simply because the power of correcting faulty exposure is frequently referred to, and the instructions might appear incomplete without it. When it is found that the exposure has been carried too far in a batch of prints and the first has been over-developed, the next should be slid under the developer and withdrawn as soon as it is completely wetted. The print should be held in the hand or laid on a sheet of glass until all the detail in the high lights that is required appears, and then placed in the clearing bath. Prints treated in this manner are seldom so bright as when correctly exposed and developed, and are frequently mealy in appearance.
It is very frequently stated that under-exposed prints may be saved by warming the developer, and it is so to a certain, though very limited, extent. The aim of the printer should be to expose the prints to the correct stage, when development becomes automatic. When a number of prints have been developed the developer becomes loaded with iron salts and in time will give faulty prints. Should the slightest falling off in quality be noted the bath should be discarded and a fresh portion taken into use. A bath that is too weak will cause platinum to float off the surface of the paper, and if anything of the sort is noticed the bath should be strengthened. After the developer has been used it is better stored in the dark.
 
Continue to: