Thus, so far as the distribution of the steam and its treatment in the cylinder is concerned, a marked advantage is shown in favor of this valve gear. But next in its favor, as before said, is that the above advantages are not gained at the cost of added complication of parts or increased cost of machinery, but the reverse, as this gear can be built at a less cost than link gear, varying according to the circumstances, but reaching as high as a saving of 25 per cent., or, if it be compared with a link gear supplemented by the usual special expansion valve and gear as employed on marine engines, then the total saving is fully 50 per cent., and an equally good result is obtained as to the distribution and subsequent treatment of the steam.

After accuracy of result and reduction in cost may rank saving room and the advantages arising therefrom (though for steamships perhaps this should have come first). Taking locomotives of the inside cylinder type, which is the general form in use in England and the continent of Europe, by clearing away the eccentrics and valves from the middle of the engine, much larger cylinders may be introduced and a higher rate of expansion employed, and this is being done. Also room is left for increasing the length and wearing surfaces of all the main bearings with even less crowding than is now the case with engines with the smaller cylinders.

But this advantage of saving room comes much more prominently forward in marine engines, especially in war ships, where every inch of room saved is valuable; and in the new type of triple-cylinder engines now coming so much into vogue in the mercantile marine, whether those engines be only the ordinary three-cylinder engines with double expansion, or the newer, triple expansion engine, expanding the steam consecutively through three cylinders - the form of marine engine which promises to come into use wherever high-class work and economy are required. On this system, by placing all the valve chests in front of the cylinders instead of between them, or in a line with them, sufficient room is saved to get the new-type three-cylinder engine into the space occupied by the old form of two-cylinder engine.

Besides these prominent advantages there are others which, though of minor importance, are still necessary to the practical and permanent success of any new mechanical arrangement, such as the accessibility of all the working parts while in motion, for examination and oiling; the ease with which any part or the whole can be stripped and cleaned, or pinned up out of the way in case of break down or accident, or got at and dismantled for ordinary repair; the ease with which the whole may be handled, started, reversed, or set at any point of expansion - all these being recommendations to enlist the care and attention of the engineers in charge by lightening their duties and rendering the engines easy to work.

With those advantages it is perhaps not surprising that this valve gear has been very considerably adopted for many classes of steam engines, especially where a high result has been required, with economy of space, and a minimum of complication.

Having crucially tested the original engine on the London and North-Western Railway, Mr. Webb proceeded to build others similar, and on his bringing out his Compound Express Engine - notably the most advanced step in locomotive design of the present day - he adopted this valve gear throughout. There are now a number of these engines running some of the fastest trains on the London and North-Western Railway, with the most satisfactory results.

Following these, others of the leading railways took up the system, and prominently among these Mr. Worsdell, of the Great Eastern Railway, built a number of large express engines for his fast and heavy traffic, and is now building a number of others similar as to the valve gear for his suburban traffic, which is specially heavy. Also the Lancashire and Yorkshire and the Midland and others of the chief railways are employing the system specially for large express engines; the Midland engines having cylinders of 19 inches diameter by 26 inches stroke, and four coupled wheels of 7 feet diameter. A number of the above-named engines have run large mileages, in many cases already exceeding 100,000 miles per engine. For other countries also a number of locomotive engines have been built or contracted for - both of inside and outside cylinder types - making a total of nearly 800 locomotives built and building, many of them being of special design and large size, up to 20 inches and 21 inches diameter of cylinder.

In all these the absence of wire-drawing may be specially noted by the full line at the top of the diagram, showing the admission of steam - this fullness arising from the rapid and full opening of the port for admission.

Passing now to the other great type of engines, those covered under the general designation of marine engines, this gear has been applied to nearly 40,000 H.P. indicated, built and building, and to all classes and sizes, from the launch engine with cylinders 8 inches by 9 inches, running at 600 to 700 revolutions per minute, up to engines for the largest class of war ships, such as her Britannic Majesty's steel cruiser Amphion, of 5,000 H.P., with cylinders in duplicate of 46 inches and 86 inches diameter, and 3 feet 3 inches stroke, running 100 revolutions per minute. An examination of the indicator diagrams taken from these engines shows that no wire-drawing takes place, and that, though the expansion is carried to a point beyond the ordinary requirements, the compression is but slightly increased. In all the diagrams taken from this valve motion there is seen the clear, full upper line showing an abundant admission of steam without any wire-drawing, and also the distinctly marked points where "cut-off" or "suppression" and where "release" takes place, showing the rapid action of the valves at those points.

It is well known to engineers that to obtain the maximum advantage out of compounding, it is necessary to cut off in the low pressure cylinder at a point corresponding to the relation between the low and the high, and that point should be unaltered, whereas the point of cut-off in the high may at the same time be varied to suit the work to be done.

In an ordinary link motion engine (where both links are connected to the same weigh shaft), when linking up the high pressure cylinder to cut-off short, the same change is necessarily made in the low. By the use of the Joy gear, cut-off valves may be fitted to both cylinders, that for the low pressure being fixed at the constant position required by the proportion of the cylinders, while that on the high is adjustable; of course, in this case, the position of the quadrants must be only changed for reversing. In arranging the independent cut-off on the Joy gear, it is only necessary to increase the length of the vibrating link beyond the point of attachment for the main valve spindle connection to obtain a point from which motion may be taken to actuate the cut-off valve; even then the cost of the Joy gear for both cylinders is but little more than for a single set of link gear.

This arrangement gives an absolutely perfect distribution of steam for compounding, also equalizes the power developed by both cylinders, and is far more simple and inexpensive than any other gear in existence.

[1]A paper read before the Mechanical Section of the British Association, at Montreal, August, 1884.