Fig. 72. The blacks in the print balanced by the black in the frame.

Fig. 72. The blacks in the print balanced by the black in the frame.

Fig . 74. Japanese print framed with mat and narrow dark frame with bead.

Fig-. 74. Japanese print framed with mat and narrow dark frame with bead.

Fig. 73. Japanese prints framed with mats and narrow frames.

Fig. 73. Japanese prints framed with mats and narrow frames.

Fig. 75. Broad frame in yellow, middle value, a little less brilliant than the sail. Maxfield Parrish's  The Pirates.

Fig. 75. Broad frame in yellow, middle value, a little less brilliant than the sail. Maxfield Parrish's "The Pirates."

To use the rabbet-plane on a narrow piece of wood, it is first necessary to make a device like that shown in Fig. 77. On a piece X, say 2" or 3" wide and slightly longer than the long members of the frame, nail a strip about 1½" wide " from one edge. Into the internal angle formed by these pieces and near one end, drive a small nail or screw (A in Fig. 77) so that its head will project about ¼", This device when used is to be fastened on the bench between a bench-stop and the tail-vise-dog. Set the rabbet-plane so that the fence allows but ½" of the cutter to cut, and set the depth gage so that the plane can cut ⅜" deep. The cutter should be adjusted so as to cut as in an ordinary plane. Along the right arris of the sole is a removeable spur which scores the wood so that the cutter will not tear out but cut out the shavings clean. Before beginning to plane see that this spur is sharp and that the right corner of the cutter is in line with the arris of the sole. Now cut a trial rabbet on a waste piece of wood, which has a straight edge. At the first stroke the spur will mark the width of the rabbet. Be careful to hold the plane flat, tilting it neither to the right nor to the left.

Fig. 76. Black frame to match the crow.

Fig. 76. Black frame to match the crow.

The beginner in his effort to keep the fence close up to the edge is apt to tilt the plane to the right. This makes the spur cut in obliquely, as in Fig. 114, Handwork in Wood.

If the plane is not running true, stop planing and with a chisel trim out the recess clean and square and then proceed with the plane to the proper depth. After sufficient practice on waste pieces, plow the rabbets on the members of the frame, as in Fig. 78. Cut the 24" piece of stock in two, so as to make one long and one short member of the picture-frame. Fasten the device already made between a bench-stop and the dog in the tail-vise. Lay one member of the frame, narrow edge up, in this device, abutting against the nail. Plow out the rabbets in all four members. The next step is to cut the pieces to their proper lengths with a miter at each end. Fig. 79 shows the shape. The picture and glass are 9½" x finished outside length of each member of the frame will be ⅝" + ⅝" or 1¼" greater than the length (and width) of the picture and of the glass. Then allow ⅛" for play and the outside lengths of the long members of the frame will be 14⅞" ( 13½" + 1¼" + ⅛") and the outside length of the short members 10⅞" (9½" + 1¼" + ⅛"). Place one member face up in the miter box, that is, so that the rabbet is down and front, as in Fig. 80. With the back-saw cut off one end at an angle of 45 degrees, taking care that the side which is to be the outside of the frame is the longer, as in Fig. 79. Do this to one end of all the pieces. Now cut the other end of one piece in the same way, except that the saw is laid in the other 45° kerf of the miter-box. Cut the other member of equal length, using the first member as a measure, and repeat with the second pair. Now test these angles with the try-square from what will be the face side of the member when in the finished frame, and again test with the bevel set at 45 degrees from what will be the edge of the frame. (See above, page 52.) If necessary trim on the bench-hook with the chisel (as above, page 52), or fasten the piece in the vise at an angle of 45 degrees and carefully plane toward the acute angle. This acute angle may be supported by a piece, X, also fastened in the vise, as in Fig. 81. Be sure the opposite members have equal lengths.