General Outline Of Work. Part 4
Description
This section is from the book "Manual Training In The Grades", by Frank Halstead. Also available from Amazon: Manual Training In The Grades.
General Outline Of Work. Part 4
Tenth Week - Model No. 3, (Continued)
Theory (Ten Minutes)
Talk on building construction. Rafters and roof.
Practice
1. Finish planing stock square and true to dimensions. 2. Lay out and cut mortise and tenon joints.
Eleventh Week - Model No. 3, (Continued)
Theory (Ten Minutes)
Talk on building construction.
(a) Boarding in.
(b) Floor, timbers, etc.
Practice
1. Finish cutting joints.
2. Lay out and cut curve. File same.
Twelfth Week - Model No. 3, (Continued.)
Theory (Ten Minutes)
Talk on building construction. Interior finish.
Practice
1. Sandpaper and scrape model.
2. Bore holes for screws.
3. Glue joints.
Thirteenth Week - Model No. 3, (Continued.)
Theory (Ten Minutes)
Talk on building construction. Lath and plaster.
Practice
1. Stain.
2. Fill and varnish.
Fourteenth Week - Model No. 4
Theory (Ten Minutes)
Staining.
(a) Kinds.
(b) Application.
Practice
1. Saw stock for model.
2. Plane stock square and true to dimensions.
Fifteenth Week - Model No. 4, (Continued)
Theory (Ten Minutes)
Filler.
(a) Kinds.
(b) Application.
Practice
1. Lay out and cut curves on sides. File same.
2. Bore holes on sides for screws.
Sixteenth Week - Model No. 4, (Continued)
Theory (Ten Minutes)
Shellac.
(a) White.
(b) Yellow.
Practice
1. Scrape and sandpaper stock. 2. Screw together.
Seventeenth Week - Model No. 4, (Continued)
Theory (Ten Minutes)
Varnish.
(a) Kinds.
(b) Uses.
Practice
1. Stain.
2. Fill.
3. Varnish.
Eighteenth Week - Model No. 4, (Continued)
Theory (Ten Minutes)
Pumice.
(a) How obtained.
(b) How used.
Practice
1. Saw stock for model.
2. Plane stock square and true to dimensions.
Nineteenth Week - Model No. 4, (Continued)
Theory (Ten Minutes)
Rotten stone.
(a) How obtained.
(b) How used.
Practice
1. Lay out and cut mortise and tenons, where necessary. 2. Bore holes for screws.
Twentieth Week - Model No. 4, (Continued)
Theory (Ten Minutes)
Review of previous questions.
Practice
1. Finish boring holes.
2. Scrape and sandpaper stock.
3. Cut curves if necessary.
Twenty-First Week - Model No. 4, (Continued)
Practice
1. Stain model.
2. Fill
3. Shellac "
4. Wax "
Twenty-Second Week - Model No. 5
Practice
1. Saw stock for model.
2. Joint stock for doors and back.
Twenty-Third Week - Model No. 5, (Continued)
Practice
1. Plane stock square and true to dimensions.
2. Curve edges where necessary.
Twenty-Fourth Week - Model No. 5, (Continued)
Practice
1. Bore holes for screws.
2. Scrape and sandpaper stock.
Twenty-Fifth Week - Model No. 5, (Continued)
Practice
1. Screw model together.
2. Place hinges on door.
Twenty-Sixth Week - Model No. 5, (Continued)
Practice
1. Stain model.
2. Fill
Twenty-Seventh Week - Model No. 6
Practice
1. Saw lumber for model.
2. Plane, etc.
Twenty-Eighth Week - Model No. 6, (Continued)
Practice
1. Finish planing stock square and true to dimensions.
2. Lay out and cut joints.
Twenty-Ninth Week - Model No. 6, (Continued)
Practice
1. Finish cutting joints.
2. Lay out curves where necessary.
3. Scrape and sandpaper.
Thirtieth Week - Model No. 6, (Continued)
Practice
1. Stain model.
2. Fill "
3. Shellac "
Extra Models To Be Used In Course: Model No. 7, Smoker's Cabinet, Two Designs
Continue to:
My Books
