This section is from the book "Rustic Carpentry", by Paul N. Hasluck. Also available from Amazon: Rustic Carpentry: Woodworking with Natural Timber.

Fig. 141. - Enlarged Cap of Tool House Pilaster.
It is suggested that at / a seat might be fixed to fold down like the leaf of a table when not


Fig. 143. - Plan of Ground Framework of Garden Snuggery.

Fig. 141. - Back Framework for Garden Snuggery. II.
The two side sills b (Fig. 143) are each 10 ft. 8 in. long, 6 in. wide, and 4 in. thick, and rest on the stones; on them lie the end sills c c, which are 8 ft. 2 in. long. These sills are halved together at the ends, and a hole is bored through them where the middle of the collar-post will rest. This hole should be bored a couple of inches into the stone, and an iron pin or dowel 8 in. long driven in; the pin will thus stand a couple of inches above the face of the sill, and will fit into a hole in the collar post.

Fig. 145. - Front Elevation of Snuggery Porch.
The joists D (Fig. 143) for supporting the floor are five in number, each being 8'ft. long, 2 1/2 in. wide, and 3 in. deep. They are halved for a distance of 2 in. at each end to fit into slots, l 1/2 in. deep, made for them in the sills, and are nailed in place. When fixed their upper surfaces are level with the sills.
The four collar-posts E (Figs. 143 and 144) are each 6 ft. 9 in. long and 4 in. square, and, when set up, their outer sides come flush with the sills. The uprights F (Figs. 143 and 144) are 3 in. square, and need to be 2 in. longer than the collar-posts, as their lower ends are halved for this distance to fit slots in the outer sides of the sills. There are four of each uprights at each side, three at the back and two at the front, the latter serving also as door cheeks. They are nailed in place with their outer sides flush with those of the collar-posts and sills.
For the rustic pillars of the portico G (Fig. 145) nothing will be more suitable than larch poles about 4 1/2 in. in diameter at the base; failing larch, fairly straight pieces of any rough, round wood could be used. The pillars are shown in Figs. 142 and 145 standing upon and dowelled to pieces of stone. When in position, their tops will be level with the collar-posts and uprights, their centres being 2 ft. 4 in. in advance of the front sill.

Fig. 146. - Side Elevation of Window-board.
On the collar-posts, uprights, and pillars are placed the wall plates H (Fig. 144), of which there are four belonging to the snuggery proper, each 5 in. wide and 3 in. thick. The side plates are 3 ft. 4 in. long, and are halved where they rest on the collar-posts and pillars, to receive the ends of the cross-plates, which are 8 ft. 2 in. long and halved to a distance of 5 in. from their ends. The wall-plates come flush with the collar-posts and uprights on which they rest, and to which they are nailed. There is also a filth wall-plate which lies along the tops of the pillars in the front. The best material to use for this would be half of a pole like those used for the pillars, the flat side resting on the pillar tops. It will be observed that the front ends of the side wall-plates project about 4 in. beyond this piece.
Ten rafters, k (Fig. 144), will be required for the roof, each 5 ft. long and 3 in. square. The two outer pairs come flush with the outer sides of the sills and wall-plates. A sixth pair of rafters to stand over the pillars and their wall-plates are made from a round pole cut in half, with the sawn side laid uppermost. The tops of the rafters butt against a ridge-piece l (Fig. 144), made of 1-in. board 4 in. deep and 13 ft. 4 in. long. As shown in Fig. 144, continuations of the uprights are in the back carried from the wall-plate to the roof, the front being treated in a similar manner.
The lintel of the doorway is 6 ft. above the sill, the door opening being 5 ft. Hi in. by 2 ft. 6 in. after the floor has been laid. The window shown in Fig. 142 is 3 ft. above the sill, and is 3 ft. high; including the two mullions, it is 5 ft. 10 in. wide. The board shown nailed in front of the window sill is sloped a little downwards to throw off the rain, whilst above there is a board 9 in. wide, nailed at a steeper slope upon brackets, as seen in Fig. 146, to shelter the window. The 3/4-in. flooring boards which are used for the floor should be bought ready planed on one side, and must be well seasoned, and cramped tightly together in laying, or there will be chinks between them. Similar boards may be used for the outside of the snuggery, being nailed to the uprights at the back and sides, as shown in Fig. 147. At the sides this weather-boarding will extend as far forward as the rustic pillars, thus enclosing the sides of the porch. For the inside of the snuggery use 1/2-in. matchboarding, as shown in Fig. 147. This may be carried up beneath the rafters to the ridge-piece. The porch may be also matchboarded throughout if desired, although this is not essential.

Fig. 147.

Fig. 148.
Figs. 147 and 148. - Sections of Snuggery Walls.
There are several methods of making the wooden walls non-conductors of heat, the most thorough being to pack the space between the inner and outer casings with sawdust. Shavings or similar materials could also be used, but less effectually. Another plan is to tack felt over the inner side of the weather-boarding before nailing up the interior casing. But even without any packing, two thicknesses of board with an air space between make a reasonably good non-conductor. Felt is fastened over the matchboard lining of the roof before the iron is put on.
 
Continue to: