This section is from the book "Amateur Work Magazine Vol3". Also available from Amazon: Amateur Work.
The planking should be either of pine, cedar, or cypress as is most convenient. It must be well seasoned and dry, in order not to check and shrink after being fastened into place. If possible, it should be in lengths long enough to extend the entire length of the boat without joints or butts, as this makes a smoother piece of work, besides being much easier. It should be noted that on account of the curvature of the side of the boat, the planks have a curve, or spiling as it is termed, which necessitates the board being considerably wider than the plank which is gotten out of it. The boards then, should be gotten as wide as is convenient, and planks worked out of them as wide as possible, up to about 6" wide. Too wide planks are not desirable, although they make fewer seams; the wide planks, however, are likely to check and split. It is not necessary that the plank should be entirely free from all knots, as small, tight knots are not at all a detriment, but rather add to the strength of the plank, and tend to prevent it from checking. Large, loose knots and weather checks, must however, be avoided. The plank should be 8/4" in thickness.
The planking may now be started. It is to be fitted on the topsides first, about four stakes being probably required. The top strake would be6t be fitted first, as it defines the sheer outline. The marks of the sheer are already on each mould and the stem, and it is only necessary to lay the plank on in place and mark it according to the marks on the moulds. With the batten, a fair line is drawn through these points. The width to be covered on each mould should be divided equally according to the number of plank it is intended to put on. The width of the top strake is then transferred from the moulds to the board, and a fair line struck through these points, thus outlining the lower edge of the plank.
The edges of the plank should be smooth and square. Where the plank joins the stem the curve can be obtained by clamping the plank on in place and marking across it to fit the rabbet. The end may then be allowed to spring out and be trimmed off to fit, the plank remaining in place. It may be sprung back and any further trimming noticed. It should De a neat fit for the rabbet and at the stern should project beyond. The plank for one side may be used as a pattern for the corresponding plank on the other side, thus saving all but the final trimming. The lower edge of one plank may also be used as a pattern for the top edge of the next plank below, and should be transferred to it before fastening in place. The top strake may now be fastened in place permanently. It should be clamped in place on the moulds and forced tightly into it6 place in the rabbet of the stem, where it is secured with brass screws or galvanized boat nails. These fastenings should be countersunk by boring in about 1/4" deep with a bit large enough to take the bead. The plank should also be fastened temporarily to each mould with long slender screws, working from the bow towards the stern. At the stern it should be fastened with brass screws, the same as at the stem. After fastening at the stern the plank should be cut off about 1" beyond and left rough. The second plank should be fitted in the same manner. The seam between planks should be close on the inside and just slightly open on the outside to allow the insertion of a thread of calking. These directions also apply to the succeeding strakes below.
The lowest strake of side planking should be fitted last. This strake extends to the lower edge of the bilge stringer and is beveled off to the same angle to take the bottom planking, This lowest strake, besides beine fastened the same as the others is also fastened permanently to the bilge stringer throughout its whole length, either with brass screws, or galvanized boat nails driven through and clinched on the inside of the bilge stringer. If nails are used they should be clinched across the grain, and care taken not to split the bilge stringer in clinching. If it should be necessary to make a butt joint in any plank the ends should be brought together to a good fit and a block abont 8" long fitted on the inside over the joint aud the ends fastened to it with boat nails, clinched over. These joints must be so placed that the blocks will come between frames. There are three of the latter between each two moulds, 9" apart on centres. The proper position for the joint can thus be easily found.
The lower edge of the lower topside plank is to be beveled off to the same angle as the bilge stringer, so that the bottom plank will lie smoothly across both. This angle can be verified by bending a thin board over the moulds and trimming off to fit. The bottom plank is next in order. This plank is put on starting next to the keel and working outwards. The gar-board strake or plank next to the keel is the first to be fitted. On account of the slope of the bottom, this plank will have a considerable amount of curvature and the "spiling" will require to be taken.
To obtain the spiling of the plank, a thin board with one straight edge is used. This board is laid on the moulds near the keel and clamped in place. The crossing of each mould is marked on the board and the distance measured from the edge of the board to the inside of the rabbet at each mould. The board is then transferred to the stock from which the plank is to be gotten out, and the same distances already measured, are laid off from the edge of the board. Through the points thus laid off a fair line is struck with the batten. The edge is trimmed to this line and is finally fitted by bending into place alongside the keel. These garboards must be very carefully fitted and lie fairly in the rabbet all fore and aft.
It is especially desirable that the garboad seam should be tight, as otherwise it is a source of much trouble and annoyance.
The upper edge of the garboard strake is left straight and at the bow is carried to meet the curve of the lower edge. This plank is fastened permanently to the back rabbet on the keel and stem and also to the sternboard if it extends so far. Owing to the width of the plank and its curvature it may taper out before reaching the sternboard, but it can be fastened securely to the keel. It is secured to the moulds with slender screws. The next, and the following planks, are cut in the same manner and fastened temporarily to the moulds with screws. The outer planks of the bottom will land across the bilge line, and are to be nailed to the bilge stringer and to the lower plank of the side. The bottom planking, where it extends beyond the bilge line, is now to be trimmed off even with the side planking and smoothed down. The bilge stringer, together with the side plank, give a double row of fastening and make a good tight joint. All the joints in the bottom should be close inside and slightly open on the outside. As fast as a plank is fitted on one side the corresponding plank on the other should be fitted, using the first as a pattern.
The frames are next to be put into place. They are of oak, or other hard wood, and are l1/2"xl 1/4", and are put into the boat with the 1 1/2" dimension vertical. As before stated, they are spaced 9" on centres, or three between each two moulds. The frames are in two parts, one extending from the keel to the bilge stringer, and the other from the bilge stringer to the deck. The bottom frames are fitted between the keel and the bilge stringer, being notched out to fit the keel, and extending on to it as far as possible, to give a good fastening to it. A nail or two should be driven through the end of the frame into the keel, taking care not to split either the end of the frame or the back rabbet of the keel. The plank should be fastened to the frames with copper or galvanized boat nails. If the latter are used they should be bored for and clinched over across the grain of the frame, and carefully, to not split it. If copper nails are used they are cut off about 1/8" above the surface, a burr, or washer is slipped on and the nail is headed over, a heavy hammer or other weight being held against the head.
The copper nails are much to be preferred, as they draw the plank up very tight. Brass screws can be used for fastening the plank in place; in many instances they have given good satisfaction, but the writer does not recommend them for this purpose. The side frames extend from the upper edge of the bilge stringer to the top of the sheer strake already in place. This frame, being 1 1/2" deep can be cut out to fit over the bilge stringer and make a clean corner with the bottom frame.
As the boat now stands she would be weak at the bilge and to remedy this, some sort of brace must be fitted. A corner angle of galvanized iron 1 1/8" x 3-16" is recommended as being very strong and taking up no room. It is fastened with rivets extending out through the plank. Fig. 9 shows the general idea of the frames and corner braces. If it is not desired to go to the expense of the corner braces, a corner piece of wood may be fitted as in Fig. 10, with the grain running as shown; a curved knee would, however, be better and would take up less space inside the boat. The tops of the side frames can be cut off even with the top of the upper strake of side planking. Towards the bow the bottom frames will require some fitting to make them conform to the twist in the surface. In fact, it will facilitate the fitting of knees and floors if all the frames are beveled so that they stand both plumb, and square with the centerline of the boat, and not square with the outline of the side.
Forward and aft of the centerboard box the frames, where they cross the keel are to have a floor, or cross piece fitted, to connect the two sides of the frame across the keel. These floors may be either of galvanized iron 1 1/3" x 3-16" or natural crook knees set on the top of the floors, or a piece of oak about 1 1/4" x 1 1/4" may be steamed and bent into place across the keel and fastened through planking. A still simple way is to use a piece of board about 3/4" thick with the grain, as shown in Fig. 11, fitted at one side of the frame. It is notched down over the keel, and fastened to the frame and also to the plank independently of the frame. This method, although quite general, is not as good as others. The frames in the way of the ce n treboard box should have angle braces fitted into the corner and screwed to the centreboard logs.
As has been before noted, there are three frames between each two moulds. Those between the moulds should be fitted completely and all the fast-enings driven and knees put into place. The moulds may now be removed and a frame put into the place of each, using the holes made for the screws, to take rivets, thus leaving fewer holes to be filled with putty. The ends of the planks, where they project beyond the sternboard, must be planed off smooth with its surface. The plank should not be planed on the outside until later. It will, however, be wise to give the planking a heavy coat of oil and then paint the inside with one coat. This will prevent its checking and shrinking during the remainder of the work. Fig. 12 shows the keel with the moulds set up in place, and the bilge stringer fitted ready for planking.
 
Continue to: